Practical Techniques and Experience Sharing for Circular Knitting Machine Setup — In actual machine adjustment, many problems do not originate from the machine itself but from the degree of match between process parameters and raw material characteristics. For example, when knitting polyester-spandex elastic fabric, if horizontal stripes, vertical stripes, or uneven density appear, do not rush to adjust the tension discs; instead, check whether the draft ratio of the spandex yarn is stable and whether the yarn feed wheel is worn. Experience shows that spandex yarn from the same batch differs noticeably in elastic recovery under different temperature and humidity conditions. During the plum rain season, the draft ratio usually needs to be about three to five percent lower than in the dry season; otherwise, faint horizontal stripes are likely to appear on the fabric surface.
During machine adjustment, it is also important to develop the habit of "look at the fabric surface first, then inspect the machine, and only then adjust parameters." The fabric surface is the most direct reflection of machine condition: skewed loops mostly point to a concentricity problem between the cylinder and the dial; thick and thin places require priority inspection of cloth roll slippage or uneven pressure on the pull rollers; and continuous holes are often related to worn sinkers or excessive clearance in the cams. It is recommended to use a magnifying glass before each adjustment to observe the fit between the needle hook and the needle slot. Needles worn by more than 0.1 mm should be replaced promptly rather than waiting until needle breakage occurs.
In addition, machine adjustment records are a valuable asset that is easily overlooked. It is recommended to establish a parameter file for each circular knitting machine, recording the machine model, cylinder diameter, gauge, raw material specifications, draft ratio, tension settings, and ambient temperature and humidity, together with corresponding fabric sample photos. Over time, this file can become the basis for rapid troubleshooting, and novice adjusters can avoid unnecessary detours. There is no fixed formula for machine adjustment; only by combining theoretical parameters with on-site observation and repeated verification can one truly achieve a clear understanding and measured control.
Another frequently overlooked step is the "first-piece confirmation" after machine adjustment. Many technicians turn away to attend to other tasks once the parameters are adjusted and the machine runs normally, only to discover half an hour later during bulk knitting that loose edges or curled edges have appeared at the fabric selvedge. The correct approach is: after adjustment is completed, knit continuously for no fewer than twenty revolutions, take three fabric samples from the beginning, middle, and end of the piece for comparison, and focus on checking width deviation, weight fluctuation, and whether the edge structure is clear. If the weight difference among the three samples exceeds two percent, it indicates that hidden problems remain in the yarn feed or pull system and re-verification is required.
In linking equipment maintenance with machine adjustment, it is also necessary to establish the awareness of "maintenance before adjustment." The cleanliness of key components such as the cylinder, dial, cams, and yarn feeders directly affects adjustment precision. Accumulated oil stains and fly lint can create false tension impressions and cause adjusters to misjudge parameters. It is recommended to thoroughly blow clean the needle slots and cam tracks with compressed air before each adjustment, and to check whether all yarn feeders are synchronized, avoiding dark stripes on the fabric caused by lag in individual yarn feed wheels. For older machines that have been in use for many years, attention should also be paid to roundness wear of the cylinder; a dial indicator should be used for inspection when necessary. Even if parameters are adjusted with great precision, machines with excessive roundness error will find it difficult to produce uniform fabric.
Finally, the transmission of machine adjustment experience cannot rely solely on word of mouth. It is recommended that workshops regularly organize review sessions of adjustment cases, compile the phenomena, troubleshooting paths, and final solutions of typical faults into illustrated comparison cards, and post them near the machines. When young adjusters encounter similar problems, they can refer to them for troubleshooting at the first opportunity, which shortens downtime and allows the experience of veteran technicians to truly accumulate. The refinement of machine adjustment technology, in the final analysis, is the continuous cycle of four stages: observation, recording, verification, and summarization.
After "first-piece confirmation," there is another process that is easily skipped: verification of the match between machine adjustment parameters and finishing processes. Greige fabric produced on a circular knitting machine is only a semi-finished product. If, during adjustment, one only watches the fabric surface on the machine and ignores shrinkage and setting changes in subsequent dyeing and finishing, the awkward situation of "looking good on the machine but failing as a finished product" often arises. For example, when knitting cotton-spandex jersey, the width and weight set on the machine must leave room for shrinkage during finishing. If the density is set too tight during adjustment, the fabric will feel stiff and have insufficient elastic recovery after dyeing and setting; conversely, if the density is too loose, the finished product is prone to width deviation. The experienced practice is: before adjustment, review historical finishing data for similar varieties, incorporate the setting shrinkage rate into the machine parameters, and after adjustment, send a short sample fabric for trial dyeing and finishing. Only after confirming that finished product indicators meet customer requirements should bulk production begin.
Another detail worth emphasizing is sensitivity to "abnormal sounds" during machine adjustment. When a circular knitting machine is running, the normal mechanical sound is uniform and continuous. Once periodic "clicking" or intermittent friction sounds appear, it is most likely a precursor to cam wear, bent needles, or lack of oil in yarn feeder bearings. Experienced adjusters often identify the problem area by sound before obvious defects appear on the fabric surface, stopping the machine in time to prevent a small hidden issue from developing into bulk holes. It is recommended that young adjusters develop the habit of "listening to the machine" while it is running and, combined with the vibration felt by touching the cylinder housing, gradually build an auditory memory of the machine's normal state.
In addition, tools used for machine adjustment must also be standardized. Measuring instruments such as tension meters, gram-weight balances, magnifying glasses, and dial indicators should be calibrated regularly to avoid parameter misjudgment caused by inaccurate tools. Wrenches and screwdrivers placed casually during adjustment must never be left near the cylinder; once they fall into moving parts, damage to needles is the least serious outcome, and cylinder scoring can be the worst. Only by incorporating these seemingly trivial details into the standard machine adjustment process can adjustment quality become truly stable and controllable.
Speaking of standard processes, one cannot fail to mention information transfer during machine adjustment shift handover. Many bulk defects are not caused by adjustment errors in a single shift but by unclear handover and unintentional parameter changes that no one knows about. It is recommended to hang a whiteboard beside the machine or use an electronic display board to clearly indicate the current knitting variety, key parameter settings, adjustments already made, and precautions, with both parties signing at shift handover. This is especially important for night-shift adjustment, when lighting and personnel condition are inferior to those on the day shift. The rule of "whoever changes a parameter records it" must be strictly enforced to avoid the situation in which the day shift starts the machine and finds abnormal fabric surface but cannot trace the cause.
One more point worth noting is the management of raw material lot numbers during machine adjustment. For yarns of the same variety but different lot numbers, even if specifications are identical, differences may exist in dyeing performance and twist stability. If lot numbers are mixed without identification during adjustment, troubleshooting becomes extremely passive once color differences or inconsistent fabric style appear in the finished product. The standard practice is: verify raw material lot numbers before adjustment, and try to use the same lot number for the same variety on the same machine; when a lot change is truly necessary, first knit a small sample to compare fabric style and weight, and proceed to formal production only after confirming there is no obvious difference, noting the lot change time and lot number in the adjustment record.
The refinement of machine adjustment technology ultimately depends on accumulated on-site effort. Parameters can be copied, but experience cannot. Young adjusters may find it useful to carry a small notebook and jot down every abnormal phenomenon, troubleshooting process, and final solution they encounter. When similar problems arise later, flipping through the notebook is often more useful than consulting a manual. Veteran technicians should also take the initiative to translate "intuitive" feel and sound into describable and comparable judgment standards, turning experience from personal skill into workshop-shared capability. Only in this way can machine adjustment levels be improved as a whole and product quality remain stable over the long term.